Без кейворда
Remove the flat tire and replace it with the spare provided.
- Before jacking up the vehicle
- Stop the vehicle on a hard, flat surface.
- Set the parking brake.
- Shift the shift lever to �P�.
- Stop the engine.
- Turn on the emergency flashers.
- Location of the spare tire, jack and tools
Taking out the jack
Remove the cover.
Unhook the rubber band and take out the jack.
Loosen and remove the jack.
Taking out the tool box
Remove the cover.
Take out the tool box.
Taking out the spare tire
Assembling the jack handle.
Remove the jack handle and the jack extension bar from the tool box and assemble by following these steps.
- Loosen the screw using a screwdriver
- Assemble the jack handle and the jack handle extension bar and tighten the screw.
Check that the screw is firmly tightened.
Insert the jack handle extension into the lowering screw.
Place a rag under the jack handle extension to protect the back door.
Lower the spare tire completely to the ground.
Pull out the spare tire and remove the holding bracket.
Replacing a flat tire
Chock the tires.
Pry off the wheel ornament, using the beveled end of the wheel ornament remover as shown.
Slightly loosen the wheel nuts (one turn).
Assembling the jack handle.
Remove the jack handle, jack extension bar and jack handle bar from the tool box and assemble by following these steps.
Assembling the jack handle.
Remove the jack handle, jack extension bar and jack handle bar from the tool box and assemble by following these steps.
- Loosen the bolts and the screw using either the jack handle or a screwdriver.
- Assemble the jack handle extension bar and the jack handle bar and tighten the bolts.
Check that the bolts are firmly tightened.
- Assemble the jack handle extension bar and the jack handle and tighten the screw.
Check that the screw is firmly tightened.
Position the jack at the jack points as shown.
Front - Under the chassis frame side rail Rear - Under the rear axle housing
Raise the vehicle until the tire is slightly raised off the ground.
Remove all the wheel nuts and the tire.
When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.
Installing the spare tire
Remove any dirt or foreign matter from the wheel contact surface.
If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, and the tire may come off the vehicle.
Install the spare tire and loosely tighten each nut by hand to approximately the same amount.
Turn the nut washers until they come into contact with the disc wheel.
Lower the vehicle.
Firmly tighten each nut two or three times in the order shown in the illustration.
Tightening torque: 97 ft�lbf (131 N�m, 13.4 kgf�m)
Reinstall the wheel ornament.
Stowing the flat/spare tire, jack and tools
Lay down the tire with the outer side facing up, and install the holding bracket.
Pull the tire towards the rear of the vehicle when raising. After raising, visually check that tire is not interfering with components.
Stow the tools and jack securely, and replace all covers.
- After completing the tire change
The tire pressure warning system must be reset.
Improper use of the tire jack may lead to death or serious injuries due to the vehicle suddenly falling off the jack.
- Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
- Only use the tire jack that comes with this vehicle for replacing a flat tire.
Do not use it on other vehicles, and do not use other tire jacks for replacing tires on this vehicle.
- Always check that the tire jack is securely set to the jack point.
- Do not raise the vehicle while someone is in it.
- When raising the vehicle, do not put an object on or under the jack.
- Do not raise the vehicle to a height greater than that required to replace the tire.
- Use a jack stand if it is necessary to get under the vehicle.
- Do not put any part of your body under the vehicle supported by a jack.
- Do not start or run the engine while your vehicle is supported by the jack.
Take particular care when lowering the vehicle to ensure that no one working on or near the vehicle may be injured.
- Replacing a flat tire
- Observe the following precautions.
Failure to do so may result in serious injury:
- Lower the spare tire completely to the ground before removing it from under the vehicle.
- Do not try to remove the wheel ornament by hand. Take due care in handling the ornament to avoid unexpected personal injury.
- Do not touch the disc wheels or the area around the brakes immediately after the vehicle has been driven.
After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these areas with hands, feet or other body parts while changing a tire, etc. may result in burns.
- Failure to follow these precautions could cause the wheel nuts to loosen and the tire to fall off, resulting in death or serious injury.
- Have the wheel nuts tightened with a torque wrench to 97 ft�lbf (131 N�m, 13.4 kgf�m) as soon as possible after changing wheels.
- When installing a tire, only use wheel nuts that have been specifically designed for that wheel.
- If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer.
- Do not attach a heavily damaged wheel ornament, as it may fly off the wheel while the vehicle is moving.
- When installing the wheel nuts, be sure to install them with the tapered ends facing inward.
- Do not drive the vehicle with a flat tire
Do not continue driving with a flat tire.
Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair.
- When stowing the flat tire
Ensure that there is no object caught between the tire and the vehicle underbody.
- When replacing the tires
When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly.
- To avoid damage to the tire pressure warning valves and transmitters
If a warning message is displayed
If you have a flat tire
If the engine will not start
If the shift lever cannot be shifted from P
If the electronic key does not operate properly
If the battery is discharged
If your vehicle overheats
If the vehicle becomes stuck
If your vehicle has to be stopped in an emergency
Toyota Land Cruiser Owners Manual
- For your information
- Before driving
- When driving
- Interior features
- Maintenance and care
- When trouble arises
- Vehicle specifications
- Reporting safety defects for U.S. owners
Categories
- Home
- Toyota Land Cruiser Owners Manual
- Toyota Land Cruiser Service Manual